Thursday, June 18, 2009

Splash




Its been a long two days but the boat was launched without incident at 7:00am this morning. I am too burned out to say much at this point. I would like to thank my friends who showed up for support and to lend a helping hand.





After I get some sleep I will write an update on the last minute projects that kept me up late at night and the synopsis of launch day. Jenny is resting quietly in her natural element by her floating dock in Salisbury on the Merrimac River. Now I worry about all the bad things that could happen while I am not there to check in on her.

More coming this weekend...

Sunday, June 14, 2009

Vroom vroom

The engine runs and runs well now.

That's nice because everything else about the day sucked. I was wet all day.



I should have listened to my gut when I saw an electrical schematic for the electronic ignition module that shows a positive and ground wire connected to the coil. My instinct told me that looked funny. I had never seen that before. But, I figured, I didn't really understand how the electronic module works (I do now) and the schematic must be right.

In the end, I decided that at worse I would fry the electronic module if I changed the wiring. That wasn't so bad since I have a spare now. I simply removed the ground wire and made it look like every other coil I have ever seen. The engine fired off on the first or second revolution and purred like the day I put it to bed four years ago.

I know I took pictures of the instrument panel with the engine running but my camera seems to have removed them :-(

Anyway, the engine ran smoothly and I let it run for about half an hour at different speeds until I felt sure it was going to keep running with no problems. Plus, I simply liked listening to the motor run fter the last few frustrating weeks.

When I finally decided it was time to move on I shut the engine down and pumped out the oil again and filled with more fresh oil. That makes two oil changes since I put in the heavy 'preservative' mix of Marvel Mystery Oil and I think I got the old yucky stuff diluted out enough (you never get all of the oil out of an Atomic Four).

Dropping the oil sump plug into the deep bilge precipitated a thorough bilge hose down. I expect it will take a couple more before the majority of dust/mud is flushed out. I also noticed that a bucket of old used hardware had tipped into the bilge so I guess I will be finding odd bits of hardware in the deep bilge for the next few years too.

With the engine running, it was time to install the propeller. I inserted the shaft through the cutless bearing, assembled the packing gland and slipped the coupling over the end of the shaft. Then I pushed the shaft in to seat the coupling. It was a little sticky so I tapped the shaft with the hammer. I was tapping a bit harder until I remembered destroying my original shaft when I hit it too hard. So I thought I would take it back out and clean up the mating surfaces a bit. Problem was, the coupling was stuck on tight; neither on nor off.

It took me nearly an hour using the socket in the middle trick that someone showed me when I first got the boat and had to pull the shaft.



The long bolts pull the coupling towards the engine. The socket in the middle stops the shaft from coming along. Turning each bolt half a turn at a time will pull the coupling off. It was slow going. At first I used a 9/16 socket and that was a problem because it was a bit too big and that too got stuck in the coupling. In the end it all came apart.

Then I spent half an hour first lightly buffing the shaft and coupling and then actually sanding the shaft and running a drill bit (forstner since that is all I had on hand that big) and a scotch brite pad on the drill motor into the coupling. The two pieces really did not want to go together. Eventually they were persuaded and the whole shebang went back together.

The shaft tube was extended last fall so that I would have more room for the attaching clamps on the hose. That extra length really cut into my working area and it was a bit fussy working with the remaining length.

I had bought some new Gore-tex dripless packing in two sizes to be sure I would have the right size on hand.



Even following the manufacturer's recomendations the packing wound up being too thick. Oh well,what's another $50 of unused material on my basement shelf... I had some plain old flax packing and lots of dripless 'putty' that gets sandwiched between the flax. I tried it the last time I launched and it worked fine so I went ahead and used it again.



The new stuff was supposed to be better but I guess I will have to wait until I decide to order it in the right size. For the record, I have a 7/8 inch shaft and the 5/16 recomended packing size was too big.

I didn't have the wrenches on hand to tighten the gland. Hopefully I will remember to tighten it before I launch. Altogether the shaft took a couple of hours to make happy. So much for dropping the old working parts back in in fifteen minutes.



Thankfully, the propeller didn't put up a fight like the coupler did.



Then I took the first steps towards cleaning up my mess.



You just never know what you are going to need so I was loathe to take anything home. I still am frankly. I would like to sail with a full complement of hardware and supplies but that just isn't going to happen.

While I was straightening up and I was preparing to go home, the sun came out. After the long cold wet day the sun made the day feel young and fresh again.

I stayed around a bit longer and ran my running rigging and tied up the mast in preparation for transport.



I was hoping to take a few days off from work but the boss started shedding tears and mumbling something about being overbooked so it looks like the next day I can work on the boat will be Wednesday the day before launch. That means I am going to be a very busy boy on Wednesday.

On that note, its past my bedtime and I need to get some sleep.

Saturday, June 13, 2009

Marching forward

If that damn engine would fire I would have made good progress. Alas, changing every part in the ignition system didn't change anything. No spark. My thinking now is that something happened when the engine was rewired. Everything checks out fine. I find voltage where I should find voltage and I find ground where I should find ground. Still, I am thinking I may have a bad connection that is just good enough to look good but under a load it fails. I have seen this with old rusty cars.

That last thing I can check -which I thought about on the ride home- is to run a jumper from the negative side of the coil straight to the battery. I already ran a jumper from the positive side of the battery - bypassing every positive power wire in the ignition system - but I didn't think to do that with a ground wire. The only other explanation is that one of the new components I just installed is bad. Highly unlikely but then again I am well past the 'likely' stage.

Other than the engine I made some decent progress today.

I started by glueing up some teak for the blocks that the stern cleats will mount on.



I would have made more progress on the bow mounted hardware except my friendly neighborhood shop that stocks a wide selection of bronze hardware has decided to stop opening for the weekends. That is a bummer.

Luckily my local hardware store had enough stainless hardware to finish my chainplate installation.



With the chainplates all bolted in I could seal them. Unfortunately, I could not get the chainplate covers I wanted in time so I am re-using my old narrow ones for just this season.



I didn't bother with screws since I will be pulling them up within a year anyway. The stern chainplate is of the wide variety that I want on all the chainplates.



With the chainplates in, I decided to continue with the rigging and install the pins that arrived from McMaster and Carr in just over 24 hours from when I ordered them. I found ordering them from McMaster to be much simpler than any marine resource I have used. They had every size of clevis pin and cotter pin that I could want and dead simple to find in their catalog too. They are a great resource.

I just started from the top and worked my way down.



I have no idea what those side tangs were for. No fractionally rigged Triton uses them. The rope is to pull wires through the mast someday.

The forestay and upper stays.


Funny, those struts are under a lot of compression and the only thing they rest on is a cotter pin. Why rigging doesn't fail more often is beyond my comprehension.



I secured the upper stays to the struts with stainless safety wire. I would have liked to have used monel but I could not find my stash and I refused to waste my time going to West Marine. Plus, my work has lots of this stainless wire. Its 'good enough' for one season.



Then I took a look at my roller furler. I will admit I was a little intimidated. More because I just didn't know what to expect. The instructions were good I guess but a little vague.

The first step was to mark the two holes that hold in the top fitting.



Heath from Northeast rigging cut my top foil to length when he made up my rigging order. He actually did a great job and packaged everything I would need and did everything he could to help speed me along - including writing his cell phone number on the box of parts. Too bad he left Northeast rigging. Actually, I have been hearing a lot of negative comments about the company so maybe Heath just didn't fit in.

After using the template to make the marks, I drilled two holes. The holes are what the self tapping screws go through to hold the two piece top fitting in place.



Then I laid out the rest of the foils and ran the forestay up inside them.



Then I just had to join the foils together. This is where the instructions were a little vague. There was a lot of 'tops' and 'fronts' and 'forwards' with no good reference to go from. Eventually, I kept staring at the parts and the logical solution became obvious.



Two plastic halves hook onto the metal joiner piece. A little tab is set in a slot on the joiner piece and the whole assembly is slid into the foil half.



Then 5200 is applied via a syringe into the screw holes and through a filler hole between the screw holes. Channels in the joiner piece allow the 5200 to flow around and fill a cavity sealing and securing the pieces together. The syringe and 5200 (plus the other tools I needed) were included with the installation kit. Thank you Harken.

Once I figured out how to join the foils, I just worked my way down and did them all.

When I got to the bottom I had to slide the halyard swivel and roller drum onto the foil and attach the bottom fitting with a Norseman type mechanical fitting. Funny, I googled for instructions on the fitting and one of the first and best hits came from www.triton381.com site. A fellow Triton owner and inspiration for my own project. You would think Norseman would have their own page with installation instructions but I guess not. Thanks Tim, for posting those instructions with pictures :-)

The norseman took a few minutes to fuss with but I am pretty happy with it. Then I slid the roller drum down and fastened it with the pin.



And then I unpinned it again so that the turnbuckle would be accesible when we step the mast. I think that is a feature riggers like and one reason they recommend this Harken Mk IV Code Zero furler. A quick pull of the pin and the roller drum slides up allowing easy access to the turnbuckle underneath.



And just because I have a tendency to forget important things, I put all the rigging pins in the chainplates so they would be there when its time to step the mast.



The engine was actually the last thing I did today (mast rigging is mandatory for launching - engine is optional since towing is another option) so after some decent progress I got stumped again by the engine. Not a great way to end a productive day.

Oh well, there is always tomorrow...

Sunday, June 7, 2009

Downs and Ups

Sorry, too much pressure to work and not enough free brain cells to take pictures this week. I started to take pictures but then stopped early.

First, the downs:

Installed new electronic ignition. Engine still does not start. At the advice of a friend I disconnected the tachometer from the coil (he had a bad tach cause his coil to stop working - tach gets signal from coil). No change. Disconnected alternator. No change. Checked voltage at the coil while cranking the engine. Found around 10.5 volts. I need to see if this is enough to trigger the electronic ignition. I think it is. The battery is brand new and fully charged last week but maybe I need to put it on a trickle charger for a few days to get that last bit out of it. I think it is unlikely that the battery is the problem. Of course I already checked the likely source and that didn't help so what else is left? I am going to order a new coil, plug wires and plugs this week. Maybe the coil is weak. Maybe I have a bad distributor wire. Cheap fix and having spares on the boat is probably a good idea anyway.

To stay productive I moved on to the rigging (or 'Ups' if you will)

What a mess. The old rigging is atrocious. That's the stuff I can find. The other stuff is lost somewhere on the basement shelving. The whole rigging system had been so cobbled together that it is impossible to tell what actually belongs where. Some pictures during disassembly would have been nice. I can't wait to completely overhaul the running rigging.

First step was to removed the heavy RG-8u coaxial cable that clangs inside the mast like the Liberty Bell. I attached a light rope to the cable as I pulled it out so I would have something to pull the new wire bundle back in next year when I get to it.

Then I rigged up the jumpers. My nice new jumpers that go along with the rest of my nice new wire rigging. I do have one picture.



Another Triton owner suggested these fittings to me at the lower ends of the jumpers. I think they area much nicer way to adjust the tension that those old rotten corroded aluminum threaded rods and nuts at the jumper struts themselves.

The I went on to connect the rest of the standing rigging. I kept a paper and pen in hand and wrote down all the little pins and fittings I needed to make the system acceptable. The old stuff really is atrocious.

When I got to the forestay I had some worry. The measurements just didn't add up in my head and didn't match what I had written down a few years ago. I wasn't sure if I needed to cut back the cable or whether the rigging shop had done that for me. I had to leave that until I had done some more research.

While I was creating a list of pins and rigging stuff I needed I did an inventory of the engine controls and what I needed there. I had no idea there were so many pins on a boat. I need to order bunches. The good news is that the engine controls are finally getting close to what I consider acceptable. At least for this season. I need a new throttle lever but that is another story. Next time I wouldn't try to save an ounce of old hardware. After 40 years the boat deserves fresh stuff.

I was going to set up the roller furler Sunday but I got a call from someone I had promised to help and that meant several hours working on another boat. My debt is paid. I wish I had the time back.

I was still really uneasy about the forestay length. A particular issue for me in this boatyard is that I am not next to the water. To launch the boat, I have to truck the boat to the water where there is a crane waiting to raise the mast. If the rigging is wrong, then I have to truck the boat back to the boatyard until the rigging can be fixed. Its a big hassle. Its a big expense. I was afraid that is what was waiting for me.

The owner of the boat next to me gave me the solution. (thanks Buzz) The two of us drew out a right triangle in the middle of the access road. Remember that 'A' squared = 'B' squared = 'C' sqared. That also means that if one leg on the right angle is 3 units long and the other leg on the right angle is 4 units long then the third leg (hypotenuse) is 5 units long. We used this to draw out a perfect right triangle (90 degree angle) in the road and then we extended the ends to match the dimensions of the boat. I forget now but I think the length from the mast step to the bow stem fitting was 10 feet (another less interesting exercise- mast step higher than bow fitting and forestay on the front of mast not in the middle) and the height of the forestay on the mast was around 29 feet. With those two end points on the right angle in place (using some paint I had in the truck we painted the marks on the road) we could measure the hypotenuse which is the actual stay length and is the the real hypotenuse of the triangle created by the deck, mast and stay. Turns out, our experiment was within an inch of what the rigger had made up for me. No trimming necessary. I will sleep much much better now.

That killed more time but I think it was worth it. I finished up the day doing small projects and installing the chainplates - well, most of them. I couldn't find one of the bolts I needed and didn't have them in my stockpile. I had many other lengths and sizes available just not the one I needed. I didn't seal any of the chainplates because I hate the old narrow chain plate covers and I am going to order some larger square shaped covers along with the rigging pins I am ordering.

I took some measurements to make the blocks for the stern cleats and bow skene chocks to mount to. I wanted to get started on those but just ran out of time. I realized the mounting area for the skene chocks is really tight underneath and I am not sure how I am going to mount them. Backing blocks are out of the question because I already have a large crude pad that backs most of the other fittings up there. It was an early exercise in boat work and I really need to go back and redo it with something more elegant. Maybe next year. In the meantime, the skene chocks are right on the edge of the deck and the hull slopes inwards slightly in a hollow shape which is a peculiar feature in this Alberg designed boat. I think after the Triton, Carl Alberg stopped with the hollow. Whatever he intended it for it didn't work apparently.

So I am wondering about the skene chocks. I could just screw them in but they might pull out if the bow gets to bucking around. I could glue them in with epoxy or 5200 and hope I never need to take them out. I am not sure yet. Details...

Sorry for the lack of pictures. It won't happen again.

Sunday, May 31, 2009

Ups and Downs

I started the day by prepping the engine for its first start in three years.

I finished the cooling system check by refilling the exchanger with an antifreeze solution.

Then I removed the spark plugs and squirted some WD40 into the cylinders and then turned the engine over by hand a few times. Then I hit the starter button and motored the engine for about 30 seconds to get the oil flowing. While motoring, I stuck my thumb over each of the spark plug holes to make sure I was getting good compression. 'Good' on an Atomic Four means it pushes my thumb out of the way. These engines have very low compression ratios.

Then I started on the fuel. The fuel tank is brand new so I poured in a gallon and checked things out. I spent several minutes looking around for leaks and such. It all looked good. The manual quantity gauge jumped right up so I made a mark at the 1 gallon point for future reference. Then I was curious as to how much of the fuel was unavailable, i.e. below the suction tube, so I put a jumper wire on the oil pressure safety switch...



... pulled the fuel hose off the carburetor and into a plastic jug ...



... turned on the ignition and found the fuel pump had no problem pulling this fuel and delivering it to the carburetor. The pump I got from Moyer Marine actually puts out WAY more fuel than the engine needs. No worries there.

Then I poured the rest of my five gallon jug of gasoline into the tank and again checked for leaks.



I also made a mark at the 5 gallon indication. The 'V' shaped tank slopes forward toward the indicator so the fuel indication rises rapidly until the wider sections of the tank start taking fuel.

Then I filled a bucket of water and put my alternate water supply hose in place and was ready to start the engine.



Sadly, nothing happened. The motor cranked but it did not come to life.

So then I started in on the troubleshooting. I removed the front spark plug and holding it against the block I cranked the engine again. There was no spark jumping across the gap in the spark plug. There was a fine mist of fuel in the cylinder though.

Then I pulled the wire going from the coil to the distributor and cranked again. No spark coming out of the coil.

Then I took the positive wires off the coil and using another jumper, momentarily applied voltage to the coil. Then I got spark.

So then I started thinking the coil was not getting the signal from the electronic ignition to fire. Per the manufacturer's instructions I ran a jumper wire from the battery directly to the coil to check for a low voltage indication. No change.

Then I pulled the distributor apart and checked the electronic ignition. There really isn't much to see and it looked fine.

Then I did it all again...

I suspect the electronic ignition since everything else seems to be working. I don't know yet if there is a way to check the electronic igntion without simply replacing it. If the wires get crossed, it can fry the unit. If power is left on for too long it can fry the unit. None of these things happened to my knowledge but it is a possibility.

So that was a big bummer. It might even be the killing blow to my launch plans. I really don't have time in my schedule for an engine that doesn't work. It worked the last time the boat was operated. I have some inquiries out there. Hopefully, I can get it resolved quickly.

Then I turned to the rigging. I needed the chainplates put back in.

A few years ago, to stop the constant leaking from the boat being outdoors (next time indoor storage!) I had filled the chainplate slots during the deck reconstruction.



I left it so that with a long drill I could drill through the holes from the botton to re-locat the slots on deck.



Using my Rotozip tool I connected the locating holes.



And then, ever so carefully, going a little bit at a time, up on deck and then down below to test it out, I cut out the holes to the proper dimensions.



I opened up the slots a bit too wide one one spot. That's okay since the stern slot had never been 'drilled and filled' to create a moisture barrier between the deck core and the hole. The other slots had been cut out, filled with thickened epoxy and then recut to the proper size during the first year that I worked on the boat.





I was just about to mix up some thickened epoxy when...



We got hit with a torrential downpour. I went below and checked for leaks there were none except for the fresh holes in the deck. I hung out down below for half an hour cleaning up and going through my random hardware bins until it became clear that my day was done.

It was good to get started on the chainplates. It feels right to be working towards making the boat sail again. The engine is a real bummer. I am launching and will be moored in a river with 3+ knots of current at times. A sail only boat is not an option here unless I have the leisure time to wait out the tidal currents (which I don't)

Highs and lows. Whether I actually win and get the boat launched on time is still in question. I guess that is what makes it all so interesting.

Saturday, May 30, 2009

Baby steps to real progress

First of all. There were a ton of little details that I don't want to talk about. As I start connecting the original equipment I find more and more flaws with it. I should have ripped it all out and started from scratch. The maintenance on this boat was terrible and I keep finding little things buggered up - apparently by some ham fisted grease monkey. I got through it. I don't feel like discussing all the problems.

The first year that I worked on the boat I covered up the engine to keep it clean. This turned into a fruitless exercise. This time I didn't bother. Now I needed to clean up the carburetor before I tried to start it up. Maybe I should have taped a plastic bag over the inlet though.



The inlet was filthy but the bowl itself looked okay. The jets looked brand new. Which they are actually. I ran the engine about 70 hours since I overhauled the carburetor.





With the carburetor cleaned up I re-installed it on the engine and rigged it properly to the controls. This is where some of the previous maintenance issues crept up. Eventually, it all worked but I may have to go back and address some concerns later.

Then I connected the fuel pump outlet to the carburetor. I forgot to take a picture. Its just a hose anyway. The last time I had a disposable fuel filter just before the carburetor inlet. I didn't bother with it this time. I have the Racor filter which should be sufficient. The little filter is just a holdover from my aircraft maintenance days where there are lots of filters in the system for backup to the backups. The only thing the little filter would protect is from a fuel pump coming apart. If it does I will deal with pieces in the fuel. Not important enough to clutter up my engine compartment further.

Then it was off to the other end; the exhaust.

The mounting for the wet muffler is rather crude but it works. I think I had a shelf in there last time but the new fuel tank gets in the way now. The muffler is now just a bit further outboard.



The muffler makes contact on three of the four corners. Getting the new hose cut to the right length was a project because the length turned out to be very critical to getting everything to fit. It doesn't fit great actually, I have some contact with the deck drain hose. I got tired of fighting to get the hose off and on and trimming just a bit here and there. Good enough for now. Add it to the 'Needs Improvement List'. (yeah right - I will get right on that!)



I had several pictures but the lighting made them all come out lousy. The new exhaust hose runs from the exhaust piping to the muffler and from the muffler to the outlet on the stern. All with double AWAB hose clamps of course. :-)

With the exhaust system connected I turned my attention to the cooling system. I had pulled the two impellors out of the pumps when I put the engine to bed so now it was time to put new impellors back in.



The raw water impellor is pretty straight forward. The pump is mounted on the front of the engine and is driven by the front driveshaft pulley. Once I got it back together I remembered that I wanted to improve the alignment left by the sloppy mechanic that originally installed the freshwater cooling system.



Add that to the 'Needs Improvement List' too.

The original water pump, once the engine was converted to freshwater cooling became the pump that pushes the antifreeze through the closed cooling system. I changed out that impellor too and greased up the shaft.



I have no idea how people service this pump without access from a nice big Bomar hatch in the cockpit.



Then I took care of a little detail that had been nagging me.



You can just see in the photo that the seacock handle hits one of the bolts that secure the seacock. After I installed the seacock, I noticed that the top end was a little loose on the base. When I tightened it, the handle came into contact with the bolt. I cut the bolt short but that didn't really fix the problem. It got better but I still couldn't open the seacock fully. So I tightened the seacock top half a little more. Tighter than I liked but I got enough of a turn for the handle to clean the bolt. I think this is kind of a stupid design flaw.

That addressed the last of my concerns with the cooling system so I moved on to the electrical system. Can anyone spot the problem?



I picked up a new battery to replace my old (and dead) battery this morning and it didn't occur to me to check which side the positive and negative posts were on. Apparently, they are not all the same. In this case, they were opposite from the old battery and my clean, no excess, battery wires wouldn't reach. In the end I made them work for now by re-routing them but I am not too happy with it as a long term solution so I am ordering more materials to re-make the battery cables.

I was a little nervous about turning on the battery swith. I had visions of large sparks and smoke. I wasn't positive about the connection on the starter solenoid and I half expected the engine to turn over when the battery was turned on. As it turns out, nothing happened. I checked for voltages and then started turning sytems on and found that everything was working normally. Its such a relief and a bit of a surprise when everything just works like it is supposed to.

The original blower motor sounded loud. I may have to replace it with a new quieter motor. Add it to 'The List'.

Finally, I changed out the oil. The engine had been left with a 50-50 mix of oil and Marvel Mystery oil (on a suggestion from Moyer Marine - aka 'The Atomic Four experts') I sucked out three quarts and put three fresh quarts in. This should get me close to a good mix. I will run the engine and then change the oil again.



And that is where it stands. I need to add coolant and bring a bucket for drawing water from inside the boat while I test run it. I also need to bring some fuel, pour it into the tank and then prime the fuel pump (which works, I bypassed the oil pressure safety switch and got the electric fuel pump running). Then pull the spark plugs, oil the cylinders and turn the engine over with the starter to get the oil flowing again. And then turn on the engine for the first time in four years.

Fingers crossed.