Sunday, November 7, 2010

All tucked in

The wind gods must not have been paying attention this weekend. With little wind, the cover took about five minutes to pull over and maybe two hours to secure, including a trip to the hardware store for more line.







I had to run to Home Despot for some spring clamps because my old ones dissapeared after the wind storm last year. Once there I got distracted by some possible future tool purchases and wound up spending a good deal of time researching tools. It was cold too. I haven't become use to that yet. Plus, with the cover on it is quite dark and my lights were... someplace else... Do I need any more excuses or does that cover me?

... and then there is the new winter work list. Thankfully, it is a bit simpler than in year's past. Somehow I think I will still be rushing to get it all done come late spring.

Things that need to happen before the next launch:

Patch the hull where I went on the rocks last time. Initially, I was thinking I would have to lay some large pieces of cloth. Now, it looks like a few small dished out patches will work fine.

I have a jib cleat next to the patch where the old fuel fill used to be. The patch was a bit rough on the underside and it is flexing. I need to do a better job before I hook the genoa up to it in a 20 kt blow.

Fix the paint on the starboard side where the fenders rubbed through it. There are also some scratches I would like to fix. One reason I chose Awlcraft 2000 over Awl-Grip was because it is supposed to be easier to fix. I will find out shortly and I have emailed the company for any repair tips. One thing I am sure about - Awlcraft scratches easier than Awl-Grip. It is quite sensitive to clumsy tool marks...

Finish that last 5% of the deck hardware installation that never seemed to happen this fall. It's the bow pulpit and a few odd fittings next to it. Easy.

I want to move the aft cleats off the blocks next to the toerail. I am not thrilled with the look and I suspect the raised cleat puts more strain on those long bronze bolts than is necessary. I plan to move the cleats inboard into the middle of the aft deck and flat on the deck; not raised on blocks. I just have to make sure they won't interfere with the wind vane rigging.

Buy and install new stanchion tubes. I have had one tube missing for two years now. Plus, I would rather have a double lifeline system anyway.

Replace the jumper strut stay hardware. I wanted to be able to adjust the jumper strut tension with the mast up so the rigger installed some sort of tensioners into the stays that tighted with some sort of thumb screw. Under load they can't be turned. I want to put real turnbuckles in there. I removed the hardware months ago and have done nothing about it. I will call my rigger soon and get moving on that.

Get the rigging on the reverse gear right. I got a surprise last season (as did the dock crew) when I ran into the dock at 3 kts because I found out too late I had no reverse gear. Well, the prop turned in reverse but wasn't accomplishing much. The atomic four has no real reverse gear. Instead it has a clamp around a planetary gear system. When the clamp tightens, the outer band stops turning and the inner rings goes the other way. You have to see a picture to see how it works... Anyway, I need to add more tension to the system for a more positive reverse.

More varnish. Always. And getting worse with every bit of wood I add. It is the cost of true beauty.

Install the rub rail brass strip. The strip was supposed to go on right after the rubrail. Somehow that kept getting pushed back. Now it needs to get done.

Finish installing the head. The head is 95% complete. I just keep cutting the final hose an inch too short. The fourth time I expect better results. I also need to add a vent fitting and hose. I should be able to manage that.

Stop the cabin leak. The last rains confirmed that I still have a leak working its way through the cabin. I still suspect the area around the port battery shelf. One corner is tight against the partial bulkhead and I think water is pooling up and getting into the cabin there. I drilled a drain hole when the shelf was intalled. Perhaps my 'drain' hole went into the bulkhead a bit and created the leak?


That's the high priority items. A much shorter and easier list than in year's past.

4 comments:

Anonymous said...

Nice post and list. Boat looks all snug now.

"The fourth time I expect better results."

That made me laugh (*with* you; not at you).

R.

Anonymous said...

Easiest things first: Though somewhat daunting when you read the manual, in actual practice that reverse gear fix takes about seven minutes. Only go ONE notch tighter for now. A weak (though stronger than before) reverse will be easier to manage on launch day than a nonexistant neutral.

-MH

Maine Sailboats said...

I'm laughing at you, not with you. Particularly about the head hose! ;<)

Britton said...

I am glad I can provide some entertainment... :)

I don't believe the reverse issue is in the motor. It was working fine before I removed the dead simple and effective original Triton mechanical linkage and replaced it with the cable setup I have now. The cable does not have the same postive action. When I set it up, I was unsure how much movement in the lever I had before the reverse started to kick in. The lever feels a bit mushy in my hand. My guess is that I need to lengthen the cable ends to get more movement and tension to the reverse side of the lever action.

I need to explore that more.

Good to know that if I DO want to adjust the A4 shift that it isn't as hard as my reading seems to suggest.